Home > Bsod While > BSOD While Copying Files - 0x0000007a & 2nd Param 0000185

BSOD While Copying Files - 0x0000007a & 2nd Param 0000185

Using updated software is especially important for multimedia applications, antivirus scanners, and CD mastering tools. A Stop 0xA message might also be due to failing or defective hardware. These are text-mode error messages that report information about the condition. Register now to gain access to all of our features, it's FREE and only takes one minute. Possible Resolutions: • Malfunctioning SCSI and Advanced Technology Attachment (ATA) hardware or drivers can also adversely affect the system's ability to read and write to disk, causing errors. http://servergeek.net/bsod-while/bsod-while-playing-hon.html

If Autochk fails to run, you can manually perform the integrity check yourself by following the instructions to run Chkdsk provided in "Stop 0x00000024 or NTFS_FILE_SYSTEM" earlier in this list. • This list of messages is a guide to individual messages and their possible causes and resolutions... Possible Resolutions: # Stop 0x3F messages can occur after installing faulty drivers or system services. How exactly does "/bin/[" work?

These are text-mode error messages that report information about the condition. There was no problem until about a week ago, when I was playing League of Legends. If so, contact the manufacturer about a possible update.

A similar Stop message, 0x23, exists for the file allocation table (FAT16 or FAT32) file systems. The system generates an exception error when using a reference to an invalid system memory address. If disabling or removing drivers resolves the issues, contact the manufacturer about a possible update. From safe mode or Recovery Console, you can use the Expand command to uncompress and copy a file to a destination location.

This is a fairly extensive list of the most common stop errors, their corrasponding codes, and recommended solutions. I have no idea what's going on. If the error occurs during Windows XP Professional setup, the problem might be due to unsupported disk controller hardware. http://newwikipost.org/topic/bDwnE3ZuZhIm5NKwL2Z3VjSJUx1ukLJL/BSOD-problem-copying-many-files.html be cautious, the problem might be a certain file(s) or dir(s).

To test hard disk or volume integrityMethod 1:1. Stop 0x000000ED or UNMOUNTABLE_BOOT_VOLUMEThe kernel mode I/O subsystem attempted to mount the boot volume and it failed. Next step is to test ram. What a list!

The kernel and HAL files for single-processor and multiprocessor systems are stored on the Windows XP Professional operating system CD using two different file names. check that I discovered that I could repro the problem by copying huge amounts of files from one drive to another... Setup copies either Ntoskrnl.exe or Ntkrnlmp.exe to your system as Ntoskrnl.exe. In some cases, drivers for new hardware are not in the Windows XP Professional Driver.cab library, and you need to provide additional drivers to complete the Windows XP setup successfully.

Join Forum | Login | Today's Posts | Tutorials | Windows 10 Forum | Windows 8 Forum Welcome to Windows 7 Forums. check my blog o Press F6, and when prompted, provide the appropriate storage controller driver (ATA or SCSI) supplied by the manufacturer. The problem might also be due to cracks, scratched traces, or If necessary, select a slower transfer rate if an update is not yet available. Values of 0xC000034 or 0xC000000E typically indicate: # Disks or storage controllers that are failing, defective, or improperly configured.

# Storage-related drivers or programs (tape management software, for example) that are

BSOD Help and Support BSOD: seems to be when copying fileshello. Sign In Use Facebook Use Twitter Use Windows Live Register now! Stop 0x0000007F or UNEXPECTED_KERNEL_MODE_TRAP The Stop 0x7F message indicates that one of three types of problems occurred in kernel-mode: • A condition that the kernel is not allowed to have or http://servergeek.net/bsod-while/bsod-trope.html Subscribe to our newsletter Sign Up Team Terms of Use Contact Policies CCM Benchmark Group health.ccm.net Home Windows XP Stop Messages Windows XP Stop Messages Stop

A CCM membership gives you access to additional options. In Check disk options, select the Scan for and attempt recovery of bad sectors check box. Possible Resolutions: # If you added new hardware recently, remove and replace the hardware to determine if it is causing or contributing to the problem.

Possible Resolutions: • A Stop 0xA message might occur after installing a faulty device driver, system service, or firmware.

For more information about the Copy or Expand commands, see Windows XP Help and Support Centre. All Rights Reserved. This error also occurs when using mismatched files, such as copying a multiprocessor HAL on to a system using a single-processor kernel (or vice versa). both hdds? –Logman Dec 25 '12 at 18:45 I'd be checking the Ram on that system as well.

An I/O status code of 0xC000009C or 0xC000016A indicates that the requested data could not be found. Use Disk Cleanup to increase available disk space. Contact the software manufacturer about possible Windows XP specific updates. http://servergeek.net/bsod-while/bsod-while-browsing.html Using updated software is especially important for backup programs, multimedia applications, antivirus scanners, DVD playback, and CD mastering tools.

First, all the applications stop responding one by one. Stop 0x0000001E or KMODE_EXCEPTION_NOT_HANDLEDThe Stop 0x1E message indicates that the Windows XP kernel detected an illegal or unknown processor instruction. For example, you might install Windows XP on an x86-based computer with the firmware ACPI enable option enabled and later decide to disable it. For more information about troubleshooting memory leaks, see Microsoft Knowledgebase articles Q177415, "How to Use Poolmon to Troubleshoot Kernel Mode Memory Leaks," and Q298102, "Finding Pool Tags Used by Third Party

Possible Resolutions: Stop 0x7A can be caused by bad sectors in the virtual memory paging file, disk controller error, virus infection, or memory hardware problems. For drivers, disable, remove, or roll back that driver to to determine if this resolves the error. In the Error-checking box, click Check Now. 5. If a driver is listed by name, disable, remove, or roll back that driver to confirm that this resolves the error.

Drivers that have used improper addresses typically cause this error. The registry editor bypasses standard safeguards, allowing settings that can damage your system, or even require you to reinstall Windows. You can also select the Automatically fix file system errors check box. You can also use Windows XP Professional recovery features such as the Last Known Good Configuration startup option, Backup, or Automated System Recovery to restore a previous working configuration.

I followed Windows 7's Action Centre advice to install the suggested newer AsMedia USB3 driver, and it seems to have... If all else fails, take the system motherboard to a repair facility for diagnostic testing. Drivers that have used improper addresses typically cause this error.Possible Resolutions: Stop 0xD1 messages can occur after installing faulty drivers or system services. Possible Resolutions: • If you added new hardware recently, remove and replace the hardware to determine if it is causing or contributing to the problem.

Disable the service or application and confirm that this resolves the error. This error most often occurs when ACPI firmware settings are changed.